Common Problems With Memory Cards

If you own a digital camera, chances are you also own a digital camera memory card. Memory cards, also referred to as flash cards, are small electronic storage devices that store digital information from your camera. Memory cards allow an individual to store photographs from their camera on the card and transfer them to a computer via a cable cord or a card reader. They also allow us to easily erase old data and replace it with new data as often or as little as we like. While memory cards are a necessity, they are not without their faults. There are many things that can go wrong with a memory device. If you are having difficulty with your memory card, you have come to the right place. Throughout this article we will discuss different things that could go wrong with your card and how to handle them.

One common complaint about memory cards is missing or corrupted data. There are many times that, after uploading files to a computer, photographs on the card may be labelled as corrupted or missing. This could occur for two reasons. The first cause of corrupted or missing data is a defective memory device. If your memory card is defective, it is suggested that you replace it as soon as possible, as it will only continue to misplace your data. If your card is not defective, a few sectors on it may have been damaged due to a sudden loss of power. If this is the case, try to format the card either on the device or on the computer. If this does not work, it is suggested that you contact the manufacturer of the card for further instructions.

Individuals also often report that their card is not being recognized by their camera or their memory card reader. If this should happen to you, first ensure that the card is inserted properly. Remove the card and replace it into the card slot. If this does not work, it is possible, once again, that your card is defective. Attempt to reformat it either on the computer or on the camera and if this does not work, contact the manufacturer.

There are several things that can go wrong with a cameras memory card. There are, however, several steps that you can take to prevent these things from happening. To avoid any problems with your memory card, never remove it from a device while data is being processed. Always ensure that the device you are using is turned off before you remove the card. It is also important to know that power loss can effect your card. Thus, any time your camera's batteries are low, remove your card, and replace it once the batteries are fully recharged.

The most important thing to know about memory cards is how to prevent problems. This is not only because they can be expensive to buy but also because they often hold many photographs that are dear to our hearts. Always take as many precautions as possible when it comes to your card and only reformat it if there are no other options available to you.

Jayda has been an online writer for nearly 2 years now. Not only does this author specialize in health, finance, and product reviews, you can also check out her latest website on Canon Powershot SX10IS which reviews and lists the best SX10IS Canon Powershot.

Read the rest of this entry »

Photos Too Light?

Flash photos come out too light (washed out) because there's too much light from the flash. Most point-and-shoot cameras don't have controls to adjust the flash, but you can fix this easily while you're taking the photos.

You can always try to tone down the brightness with software on your PC after the fact. Ignore any advice from the pro's about using Photoshop -- it will cost far more than you can imagine and take days to learn how to use it. Many simple photo programs and photo websites have an 'Auto-Fix' button -- try that first, then you can tinker with Brightness and Contrast settings.

You'll be much better off if you can simply get a good snapshot in the first place. Here's how...

Your camera has a Zoom control. Back away from your subject a foot or two, then zoom in so they still fill up the frame, then take the photo. This extra distance makes the flash weaker so your photos won't come out too light.

The best way to get it "just right" is to practice ahead of time. Your camera will give you much better results if you know how far away to stand from your subjects to expose them properly. Don't be afraid to take a few shots, each at a different distance, so you can choose the best of the bunch.

Once you've found the right distance, here's an easy way to duplicate it each time. Just imagine your own height between you and your subject. So, if you're almost six feet tall, imagine your height as the distance to your subject. If you learn that a little further away gives you the best results, just step back a bit further than your height. As you move further away, light from the flash becomes less important, and the room lighting starts to take over. Move too far (over 10 feet) and the flash has little or no effect -- it's all room (or other available) light.

Don't forget to Zoom in so your subjects fill the frame, or you'll end up with tiny faces that aren't very interesting. You can even zoom in so you get just their faces without fear of being too light (washed out).

If your photos are too dark, you may have turned the flash off (there's a switch for that) or you may be too far away (the flash only works from about 5 to 10 feet away).

The flash usually has a setting for 'red-eye' that makes it wink a few times before actually taking the shot, flash always off, flash always on, and flash auto-fires only when it's needed. Look around and you may find settings for sports (fast action), night shots (a moon), fireworks, and much more. You paid for those features, so you might as well use them when you need them. Most cameras double as a video camera, and/or can take a long, rapid series of still shots.

If you're forced to take snapshots in very low light, many cameras have a 'night time' setting. Whether you use it or not, there are also a few tricks you can use to get good results in very low light. First, turn off the flash if your subject is over 10 feet away so the camera knows to use the available light. Most cameras have a control to change the ASA or ISO or (Film) Speed -- this makes the camera much more sensitive to light (ASA 100 needs lots of light, ASA 1600 takes photos by candlelight). Many cameras let you slow the Shutter Speed, (perhaps as slow as 1/30th, 1/15th, or even 1/4 second) but this requires holding the camera very steady. Hold it against a wall or other solid spot, or put it on a tripod or table and use the built-in 10-second timer (to avoid shaking it with your shutter finger). Try different settings until you get a good result.

Fortunately, when you view your photos later, they probably include some background information on the shutter speed, film speed, flash settings and more, but you may have to noodle around to find that information. Your manual should tell you how.

If you've lost track of your camera's manual, do a Google search for your brand model manual PDF, save a copy on your hard drive so you'll always have it handy.

Finally, the best way to take good photos is to take lots of photos. As you see your results, you'll learn what works, what doesn't work, and what your equipment and skill can get away with.

You can't take too many photos with a digital camera!

Charlie Gosh has written lots of helpful articles that show anyone how you can save money, improve your life, save time, and other interesting topics.

They have to be easy to do, or people won't do them, so the emphasis is always on doing things a different way that's easier, yet still saves money and time.

Many of the things that frustrate us the most can be fixed easily if we only knew how. Read Charlie's articles, and you'll find your life getting easier, your wallet fuller, and your frustrations floating away.

Read the rest of this entry »